This and That

Evening folks,
Just tackled a few little things today.  I took the heater bonnet duct off to paint it the correct color, a wrinkle black.  Then I re-did the data plate and got it correct this time around, then on to trying to fix the seats.  The seat were FROZEN in place and it took a long lever and my lovely wife to get them to move far enough that I could get to the fasteners.  I had tried penetrating oil to no avail!

The heater duct in it's gaudy red.



Changed to wrinkle black

The new Data plate properly riveted in place.

This doesn't look like much but I was ready to give up on getting these seats to move forward enough that I could remove them.  The previous installer reversed the seat back hinges so that the lever for tilting them was on the inside where they bind on the cubby /center console.


The other thing that should be addressed is the cubby lid, I suspect that they used incorrect fasteners and it's loose.  We'll see.

That's all for today,

Cheers,

Lynn

2 hrs


Comments

Post a Comment

Popular posts from this blog

One last post

Image
As regular readers will know I was patting myself on the back for having sorted out the electrics on the wipers a few weeks ago.  Yesterday while doing a final inspection the dang wipers would not park.  In desperation I got out my manual for the Series 3 only to find this terse comment.   So since taking the wiper motor entails taking half the car apart I decided that CJ could have manually parked wipers and pulled the Green/red lead off the wiper switch.  CJ now has OFF, SLOW and SLOWER positions on the switch.  Someday If I have the time perhaps we can pull it out and see if it's something that can be repaired. Next, I got to thinking that I couldn't send CJ home with a vibration at 60 mph!  So up in the air she went and all the tires needed a little help one as much as 2 oz.   Hopefully that will take care of the vibration! One of the better balanced wheels After moving the weights and adding a bit.  I've had really good results with using this Bubbl
Read more

Front Suspension, hubs and so forth

Image
It was nice to have a day that wasn't interrupted by a trip into town,  the front suspension is installed and ready to rock and roll. Well, roll at least. I spent a fair amount of time this afternoon trying to get the splash pans installed having to make a bracket along the way.  The pictures start with the fitment of the calipers to the uprights.  I've used lock washer, Loctite, and safety wire. Probably overkill but when your talking about stopping.... I touched up the rivets that I used to plug the holes in the frame rails with primer and then mixed up a little paint that is pretty close to the correct color. I used 50 lb safety wire, it should be set up so that loosening of one bolt will tighten the other, I think it was used extensively in the aircraft industry.  Just showing the now complete front suspension, no splash pans though Same thing on the passenger side, the bearings were set to 1-2/1000" free-play. Split pins in place and suspens
Read more

Wrapping it up, part II

Image
Evening folks, Have  few little thing yet to do, the battery tray and hold down didn't fit the battery in the car so will have to wait on that.  Got the exhaust mounting plate installed that allows one to raise the car safely from under the IRS when work needs to be done on the back end. Then adjusted the clutch slave rod to get the correct setting of 1/16" and then added the return spring that reduces wear on the throwout bearing by keeping the clutch fork back a preset distance. The correct bridge piece for the resonators  Now able to fit a block in place for jacking up the car Setting the correct 1/16" play in the clutch rod.  using a 1/16" drill bit to set a space between the lock nut and yoke with the yoke snug against it's stop then turn the rod in to meet the lock nut, tighten and then install the return spring. Took your car out for a test drive this afternoon and it did well, tracks straight and the steering wheel is centered, s
Read more